Mold remediation referrals for Philadelphia & nearby townsCall: (215) 774-2847
(215) 774-2847

How much does mold remediation cost in Philadelphia?

moldremediationphiladelphia.net

A Philadelphia cost guide puts mold remediation at $13 to $25 per square foot of affected area, while national guides describe whole jobs from roughly $1,200 up to $9,000 for a typical range. Where your own bid lands depends on the amount of material involved, the location in the house and the rebuilding that follows.

Need mold help now?
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

A Philadelphia cost guide puts mold remediation at $13 to $25 per square foot of affected area, while national guides describe whole jobs from roughly $1,200 up to $9,000 for a typical range. Where your own bid lands depends on the amount of material involved, the location in the house and the rebuilding that follows.

Quick cost estimator

Typical ranges from the sources cited below, not a quote. The company you hire will price the actual job.

Where the published numbers sit

The one source we have that is specific to this city quotes $13 to $25 per square foot of affected area. Scaled up, that is $1,300 to $2,500 for a 100 square foot project, $6,300 to $12,700 for 500 square feet and $12,700 to $25,300 for 1,000. National guides, which do not look at Philadelphia, describe typical whole jobs starting near $1,200 to $1,500 and ending anywhere from $3,750 to $9,000. All of that is estimate territory. A real bid can come in outside it.

The calculator on this page sets each range beside the area it covers. Use it as a yardstick when you hold a written bid. Do not use it to forecast one: the per-square-foot figure and the whole-job figures disagree because small jobs carry setup costs that stay put however small the stain is.

What drives a bid up or down

Labor, containment and disposal make up most of the price. The crew closes off the work zone, manages airflow, takes out or cleans what is affected, then dries and cleans the room. Two jobs that begin as the same dark patch can end up far apart.

  • Extent. More affected material costs more, though very small jobs often meet a minimum charge.
  • What the mold is growing on. Framing can often be cleaned on the surface. Drywall, insulation and carpet padding that have absorbed moisture are usually removed and replaced.
  • Access. A tight rowhouse cellar, a low attic or a wall that must be opened adds hours.
  • The cause. If water is still getting in, cleanup is only one line on the bill. A leaking drain, a worn flat roof or a seeping foundation wall belongs to another trade, and it has to be fixed first.
  • Putting it back. Many bids stop at removal and cleaning. One national guide lists drywall replacement at $1.50 to $3.50 per square foot as its own cost, and paint, insulation and flooring may come as further items.

Published ranges by part of the house

These are national figures from published guides. The Philadelphia source prices by area instead of by room.

  • Basement. One guide lists $1,500 to $6,000 for part of a basement and $6,000 to $15,000 for all of it; another shows $500 to $3,000. Cellars account for many local jobs, from stone-walled rowhouse basements to block foundations in post-war suburbs. See basement mold removal in Philadelphia and the guide to mold in rowhouse and twin basements.
  • Attic. $1,500 to $6,000 for a partial attic and $6,000 to $15,000 for a full one in one guide; $1,000 to $4,000 in another. Winter condensation is a frequent culprit, covered on the attic mold removal page.
  • HVAC and ductwork. $2,000 to $10,000 for a system, or $600 to $2,000 for duct mold removal alone, depending on the guide.
  • Walls. $1,000 to $12,000 in a national guide. The spread reflects how much of the wall must come open.
  • Black mold. $2,000 to $10,000 in one guide and $800 to $7,000 in another. Color does not set the price; scope does. Black mold facts explains what the color does and does not tell you.
  • Water damage plus mold. $2,700 to $10,000 in one national guide for a job that includes drying.

Inspection and testing come first, and they cost extra

Spending often begins before anything is removed. A national guide shows an inspection of an average home at $300 to $650, and two more put the typical range at roughly $300 to $1,000. Sampling is priced on top in a national guide: $250 to $350 for a basic air test, $250 to $700 for extensive air testing and $200 to $300 per surface swab. None of these are Philadelphia quotes.

Unsure which one you need? Mold inspection vs mold testing lays out the difference. EPA says that in most cases, when mold growth is visible, sampling is unnecessary, so an obvious patch may not need a lab at all. The Philadelphia mold inspection page describes what a visit looks like.

No published figure for clearance testing turned up, so none appears here. Request one in writing, and read post-remediation clearance testing to judge whether you want it.

When the patch is small

EPA says that for an area under about 10 square feet a homeowner can usually manage the cleanup, and the Pennsylvania Department of Health gives the same threshold for people without health problems. That department adds that you should bring in a contractor when the area is bigger or when anyone at home has asthma, COPD, is pregnant or has another health issue. A small hard-surface patch may be your least costly route; the DIY vs professional guide shows where the line falls.

Comparing bids on equal terms

Bids that seem miles apart often describe different work. Match the scope before you look at the totals.

  1. Get the scope on paper. Affected square footage, which surfaces come out and which get cleaned, and where containment is set up.
  2. Find the exclusions. Is rebuilding drywall, insulation, trim and flooring in the number, or is it demolition and cleaning only?
  3. Ask about the water. A bid that never mentions where the moisture comes from is incomplete.
  4. Check registration. In Pennsylvania, search the Attorney General's contractor lookup before signing. Hiring a mold company in PA, NJ or Delaware covers the checks in all three states.
  5. Read the contract. In Pennsylvania, work over $500 needs a written contract stating the total price, estimated start and completion dates and a description of the work.

Keeping the total manageable

Speed and source control do more for the total than negotiation. EPA says water-damaged areas and items should be dried within 24 to 48 hours, which is why a wall that was dried on the second day is a smaller problem than one left for a fortnight. Take photographs before anything is torn out and jot down when the water event happened. When a drain line or a rowhouse roof is behind it, repair that first so you do not buy the same cleanup twice. For pipe trouble, leak and burst pipe mold removal explains how drying and remediation fit together, and after a storm mold after a flood or heavy rain covers the first 48 hours.

Does the town matter?

Only Philadelphia has a local source here; the rest are national. We cannot honestly say one suburb costs more than another. Home size, age, access and scope matter more than the zip code. If you live outside the city, begin with the areas we cover and the full list of services to find the job type that fits what you found.

A word on bundled and phased work

Some companies split a large job into stages, such as emergency drying first, then removal, then rebuild, and price each stage on its own. That can make the total easier to follow, and it lets you see which lines are cleanup and which are carpentry. Ask whether the stages can be bid separately and whether a different trade can handle the rebuild.

Insurance and renters

Coverage turns on the cause of the loss and the wording of the policy, so call your insurer before work starts. Renters have a different path: the Pennsylvania Attorney General's tenant guide says every lease carries an implied warranty of habitability and that a tenant should tell the landlord and allow a fair chance to correct things. See mold in a rental for the basics.

Making the call

To reach a local company that works in your town, you can begin now.

Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847
Say what you have found and the call goes to an independent company serving your area. Mold Remediation Philadelphia is a referral service, not a mold company, and you and that company agree on the price.

Frequently asked questions

How much does mold remediation cost in Philadelphia?
A Philadelphia cost guide gives $13 to $25 per square foot of affected area, or $1,300 to $2,500 for a 100 square foot project. National guides describe typical whole jobs from about $1,200 to $9,000. These are published estimates, not quotes.
Is mold inspection included in the remediation price?
Usually not. A national guide lists an average-home inspection at $300 to $650 as its own line, and testing is priced on top of that.
Why are two quotes so different?
They often describe different scopes. One may include rebuilding drywall and insulation while another stops at removal and cleaning, or they may assume different containment. Ask both to write the scope down.
Do I need to hire someone for a small patch of mold?
EPA says a homeowner can usually handle an area under about 10 square feet, and the Pennsylvania Department of Health gives the same threshold for people without health problems. Larger areas, or anyone with asthma or other health issues, should involve a contractor or a doctor.
Does homeowners insurance pay for mold cleanup?
It depends on what caused the damage and on your policy wording. Ask your insurer before work begins and keep written records and photos.
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

Last updated:

☎ Call (215) 774-2847