Mold remediation referrals for Philadelphia & nearby townsCall: (215) 774-2847
(215) 774-2847

Mold after a flood or heavy rain around Philadelphia: first 48 hours

moldremediationphiladelphia.net

A single afternoon of thunderstorms, tropical-storm remnants or a nor'easter can send water into a Philadelphia-area basement or soak a roof and the ceiling below it. What you do in the next two days largely decides whether mold takes hold.

Need mold help now?
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

A single afternoon of thunderstorms, tropical-storm remnants or a nor'easter can send water into a Philadelphia-area basement or soak a roof and the ceiling below it. What you do in the next two days largely decides whether mold takes hold.

Why the first 48 hours matter

Drying fast is the whole game. EPA states that water-damaged areas and items should be dried within 24 to 48 hours to prevent mold growth. Spores are already floating in everyday indoor air; what they lack is a wet surface with something edible on it, such as drywall paper, framing lumber, carpet pad, insulation, cardboard or stored fabric. A wet Philadelphia basement in July, with air that is already humid, will not dry on its own. A wet one in January can stay damp for weeks behind finished walls because cold masonry never gets warm enough to release the water.

Around here the water comes in a few different ways, and the type matters. Creeks and rivers such as the Schuylkill, the Wissahickon, the Pennypack, the Neshaminy and the Cooper can rise fast in a heavy storm and push water into low streets and lower levels. Old sewer and drain lines can back up when the system is overloaded. Rain can also find its way through a roof, a flashing detail or a rowhouse parapet, and water can run down a party wall for days before it shows on a ceiling. Each of these is a different job.

Safety comes before mold

Mold is the second problem. Before anything else, ask whether the space is safe to enter. Never wade through a flooded basement while the power is on, and never handle a panel, outlet or appliance with wet feet. Have a qualified person check the electrical system before it is switched back on. If water has been in a basement with a furnace, water heater or other equipment, treat those as needing a professional look before they run again. If you smell gas or are unsure whether the structure is sound, leave and get help. Dry walls and dry floors can wait a day. Your safety cannot.

Standing water that came from outside, or from a backed-up drain, can carry dirt and contamination. Wear boots, gloves and eye protection, keep children and pets out, and ask your doctor about any health concerns. For mold itself, the Pennsylvania Department of Health says to hire a contractor if the area is larger than about 10 square feet or if someone in the home has asthma, COPD, is pregnant or has other health issues.

The order of work in the first hours

  1. Cut off the supply. A failed pipe or fitting means closing the shutoff. With storm water or a backed-up drain, the supply is outside your control, so concentrate on pumping out and keeping more from entering. A tarp over a damaged roof section helps if you can place it without climbing into danger.
  2. Record everything. Photos and video of the water line, the damaged items and the rooms, taken before you move anything, support an insurance claim and help any company you call.
  3. Move air. With power confirmed safe, bring in fans and a dehumidifier. Open windows only when the air outside is drier than the air inside. On a muggy Delaware Valley afternoon that is often not the case.
  4. Pump and vacuum. A wet-vac and a sump pump do most of the early work. Get furniture and boxes up off wet floors.
  5. Sort the salvage from the trash. Carpet pad, wet insulation, soggy cardboard and fabric that stayed soaked are the likeliest to grow mold and the hardest to clean. Bag them and carry them out.
  6. Read the humidity. EPA suggests keeping indoor humidity below 60 percent, ideally between 30 and 50 percent. A basic hygrometer shows whether the drying is working.

Basements, sump pumps and the rowhouse problem

Many Philadelphia homes are brick or stone rowhouses and twins with basements that were never built to stay dry through a major storm. Water comes through the foundation wall, up through the floor, or around a cellar window, and a sump pit that is undersized or has lost power will not keep up. If your sump pump has a battery backup, check that it is actually running. If you have a basement that floods every time it rains hard, the pattern matters more than any single cleanup, and our guide to mold in rowhouse and twin basements covers the causes. For the cleanup itself, the page on basement mold removal in Philadelphia shows what a job usually involves.

In a row of attached homes, a neighbor's water problem can become yours. Wet party walls, shared drain lines and a flat roof that ponds can all carry moisture from one house to the next. If the stain or smell is on a shared wall, tell the neighbor, because fixing only your side may not solve it.

Flood water versus a roof leak or a burst pipe

Water is not all alike. Rain that came through a roof, or a plumbing leak, calls for a different approach than water that rose from the ground or out of a drain, because flood water can bring in mud and contamination and that changes how materials get handled. Asking a mold company early beats guessing. If the water came from a pipe, our page on leak and burst pipe mold removal in Philadelphia covers that case, and the page on storm and flood mold removal covers the outside-water case.

Cold snaps matter here too. Older homes with galvanized or cast-iron plumbing in unheated spaces can have a pipe freeze and split, and a pipe that bursts inside a wall while you are away can soak a cavity for days before anyone sees it.

What to dry, what to open, and what to leave alone

Standing water on a floor is the easy part. Moisture hides inside plaster and drywall, under cabinets, behind baseboards and in the insulation over a ceiling that took a leak, and a wall can feel dry on the surface while it is wet inside. If the water reached drywall or plaster, a pro with a moisture meter can tell you whether the cavity needs to be opened. If you want a second set of eyes before anything is torn out, a mold inspection in Philadelphia can check moisture readings and look for growth.

Never seal wet materials behind paint, fresh drywall or new flooring. A covered damp wall is how a small, visible problem turns into a hidden one that announces itself months later as an odor. If a musty odor appears and you cannot see the source, the guide on a musty smell with no visible mold walks through where to look.

Mistakes to avoid

  • Mixing products. EPA warns never to mix chlorine bleach with cleaners that contain ammonia, and says biocides such as bleach are not recommended as a routine practice during mold cleanup.
  • Restarting a furnace or air handler that sat in water before it is checked. Ducts and equipment that took on water can carry trouble through the house; see HVAC and duct mold removal in Philadelphia.
  • Holding off until mold is visible. By then growth is usually well established.
  • Treating a roof leak as only a roofer's problem. Wet insulation and sheathing often explain ceiling stains that appear weeks later.

When it is a DIY job and when it is not

EPA says that if the moldy area is less than about 10 square feet, a homeowner can usually handle the cleanup, and the Pennsylvania Department of Health gives the same 10 square foot line. After a genuine flood the affected area tends to be far bigger than that, and it usually takes in wall cavities and belongings you cannot easily inspect. Our guide to DIY mold cleanup versus hiring a pro lays out where that line sits.

Pennsylvania has no state mold license, so check the basics yourself. The Pennsylvania Department of Health states there are no federal or Pennsylvania state regulations about mold. What you can verify is a company's home improvement contractor registration with the Attorney General, and in the city, Philadelphia's contractor license rules and L&I permits. Our guide to hiring a mold company in PA, NJ or Delaware has the checklist. If you are across the river in New Jersey or in Delaware, the rules differ: New Jersey has no state certification program for mold companies and requires home improvement contractor registration, and Delaware contractors need a business license from the Division of Revenue.

What it can cost

Price follows the size of the wet area and how long it sat. As a rough frame, a Philadelphia cost guide gives about $13 to $25 per square foot for mold remediation, with a 100 square foot project at about $1,300 to $2,500. National figures put a partial basement at $1,500 to $6,000 and a full basement at $6,000 to $15,000. Those are published ranges, not quotes, and flood work with contents and wall removal can land outside them. The detail is in our mold remediation cost guide.

Calling for help

Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

Say where the water came from, how long ago and which rooms got wet; from that, a company can usually tell whether to begin with an inspection or move straight to drying and removal. If you are outside the city, a page such as mold removal in Upper Darby or mold removal in Norristown shows how we cover your area.

The 48 hours at a glance

  • First two hours: get safe, stop the source, take photos.
  • Hours two through twelve: pump out, pull soaked pad and contents, start fans and the dehumidifier.
  • Hours twelve through twenty-four: look at wall bases and cabinets for trapped water, then phone your insurer and a mold company.
  • Hours twenty-four through forty-eight: confirm humidity is falling, keep air moving, and keep everything wet open.

Anything still damp at the two-day mark is a reason to call rather than wait.

Frequently asked questions

How fast does mold grow after a flood near Philadelphia?
EPA says water-damaged areas and items should be dried within 24 to 48 hours to prevent mold growth. In a humid summer basement it is best to treat that window as firm.
Can I clean flood-related mold myself?
EPA and the Pennsylvania Department of Health both put the homeowner line at about 10 square feet. The state also says to hire a contractor if someone in the home has asthma, COPD or other health issues. Larger areas or mold inside walls call for a mold company.
Does Pennsylvania require a mold license?
No. The Pennsylvania Department of Health says there are no federal or Pennsylvania state regulations about mold. You can still check a company's home improvement contractor registration with the Attorney General.
Does insurance pay for mold after a storm?
That depends on your policy and on how the water got in, so ask your insurer directly and keep your photos and receipts. A mold company cannot answer coverage questions for you.
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

Last updated:

☎ Call (215) 774-2847