Mold remediation referrals for Philadelphia & nearby townsCall: (215) 774-2847
(215) 774-2847

Mold in rowhouse and twin basements: causes and fixes

moldremediationphiladelphia.net

A brick or stone basement in a Philadelphia rowhouse or twin has been taking on moisture for a long time, and mold is usually the visible result of a moisture problem rather than the problem itself. Here is where the water comes from, how to tell, and what actually fixes it.

Need mold help now?
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

A brick or stone basement in a Philadelphia rowhouse or twin has been taking on moisture for a long time, and mold is usually the visible result of a moisture problem rather than the problem itself. Here is where the water comes from, how to tell, and what actually fixes it.

Why these basements are different

Much of Philadelphia, and many river towns and older inner suburbs, is built from attached rowhouses and twins on brick or stone foundations. Those walls were laid long before anyone worried about vapor barriers or interior drainage. Stone and brick wick moisture from the soil, mortar joints open up over decades, and the basement floor is often old concrete poured over damp ground. Add a cold winter outside and a humid summer, and a basement can swing between damp and dripping without anything being obviously broken.

The Pennsylvania Department of Health says mold could be in a home with water leaks or damp areas, and advises repairing leaks and using a dehumidifier and vent fans. The New Jersey Department of Health puts it simply: mold problems usually occur when there is excess water. That points to the order of work. Fix the water first, then deal with the growth. Cleaning mold off a wall that keeps getting wet only buys a few weeks.

Where the moisture comes from

Groundwater and the foundation wall

After heavy rain the ground around an old foundation saturates, and water moves through the wall, through cracks, or up through the floor slab. White powdery deposits on stone or brick are a sign that water has been moving through the wall and leaving minerals behind. Dark staining low on the wall points the same way.

Surface water and the roof

Downspouts that dump next to the wall, a sidewalk or yard that slopes toward the house, and a shared alley that collects water all feed the foundation. In a row, the water from a flat roof often runs through a downspout or internal drain that ends near your basement wall. A clogged gutter or cracked downspout connector can quietly soak the same section of wall for years.

Plumbing and drain lines

Older homes often have galvanized supply pipes and cast-iron drains. A weeping joint on a drain line, a dripping supply fitting or a failed washing machine hose adds water you may never notice until a stain appears. If the damp spot is below a bathroom or kitchen, look at the plumbing before you look at the foundation. Our page on leak and burst pipe mold removal covers the aftermath of that kind of leak.

Humid air and condensation

In summer, warm humid air from outside meets cool basement walls and pipes, and water condenses on them. A basement can feel clammy and smell musty with no leak at all. Cold-water pipes sweating, a dryer vented into the basement and a basement bathroom with no fan all add to it. EPA suggests keeping indoor humidity below 60 percent, ideally between 30 and 50 percent, and a basic hygrometer will tell you where yours sits.

The party wall

In a row, one of your basement walls is shared with the neighbor. A leak on their side, an old stained wall that was never repaired, or a long-abandoned plumbing line can feed damp into your wall. If the problem is on the shared wall and you cannot find a cause on your side, a conversation next door is part of the fix.

How to tell what you have

  • Tape test for condensation. Tape a square of foil to a damp wall for a day. Moisture on the outside of the foil points to humid air; moisture underneath points to water moving through the wall.
  • Watch the pattern. Worse after rain suggests exterior water. Worse in summer suggests condensation. A damp spot that does not change points toward plumbing.
  • Look at the contents. Mold on cardboard boxes, wood shelves, furniture legs and the bottom of stored fabric is common because those materials hold moisture and feed growth.
  • Check the mechanicals. A furnace, water heater, ducts and a dehumidifier drain that is not draining are all worth a look.

If you cannot tell, a mold inspection in Philadelphia is a way to find the moisture source and see how far the growth runs. EPA says that in most cases, if visible mold growth is present, sampling is unnecessary, so ask what a sampling plan would add before paying for one. Our guide on mold inspection versus mold testing explains the difference.

What actually fixes it

  1. Move water away from the house. Extend downspouts, clear gutters, and regrade or patch the surface where water pools against the wall.
  2. Repair leaks. Fix any dripping pipe, drain joint or appliance hose, and make sure the dryer is vented outdoors.
  3. Manage a sump pit. If the basement has a sump, make sure the pump runs, the discharge goes away from the house, and a power loss does not leave you without it.
  4. Control humidity. Run a dehumidifier sized for the space and drain it to a floor drain or pump. Keep the number in EPA's range.
  5. Clean or remove what grew. Hard surfaces such as masonry and concrete can usually be cleaned. Porous items such as carpet, paper and cardboard that stayed wet often cannot.
  6. Do not paint over it. Painting a damp or moldy wall hides the problem and usually peels. Dry first.

Waterproofing work beyond these steps, such as interior drains, exterior excavation or wall repair, is a construction job and a decision for you and a waterproofing or masonry contractor. A mold company deals with the growth, and the two jobs fit together. Reach for a mold company when the area is large or when the cause has been fixed and what is left is mold.

What a mold company usually does in a basement

On a typical job the crew sets up containment so spores do not spread upstairs, removes porous materials that cannot be saved, cleans or removes growth from framing and masonry, uses HEPA filtration and dries the space. For the process in order, see our guide to what happens during mold remediation. The scope on a stone-wall basement is different from a finished drywall basement, because masonry can be cleaned in place while drywall and trim usually come out.

If the basement has finished walls, an old paneled room or a drop ceiling, mold can sit behind them. A company may open a small section to see what is back there, which is more honest than guessing.

Permits and checks in the city

Philadelphia's L&I says a building permit is required for projects that change the interior or exterior of an existing structure or involve major repairs, and that ordinary maintenance repairs generally need no permit. It also says gypsum wallboard installed over existing wall surfaces in one- or two-family homes does not need a permit. If your job goes further, ask the contractor who is handling permits. The City also requires a contractor license for most construction and repair businesses, with an exemption for those working only on existing one- or two-family homes, who must register with the state as a home improvement contractor.

That state registration is with the Pennsylvania Attorney General. For work over $500 the contract must be in writing and signed by both parties, the registration number ("PA" plus a number) must appear on the contract and in ads, and the contract must include the three-day right to cancel. The Pennsylvania Department of Health states there are no federal or Pennsylvania state regulations about mold, so there is no state mold license to ask for. The hiring checklist lists the questions that matter. If your house is across the river in New Jersey or in Delaware, the rules differ.

What it can cost

Costs vary with size and condition. A Philadelphia cost guide gives about $13 to $25 per square foot for mold remediation, with a 500 square foot project at about $6,300 to $12,700. National figures from HomeGuide put a partial basement at $1,500 to $6,000 and a full basement at $6,000 to $15,000. These are published ranges, not quotes, and waterproofing is a separate cost. See the cost guide for more.

Next step

Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

Tell the person you reach whether it is a row home, twin or detached, how big the basement is, whether it floods, and whether the walls are finished. If you are outside the city limits, the pages for mold removal in Darby or mold removal in Conshohocken cover towns with similar older housing. If a flood is what started the problem, read what to do in the first 48 hours as well.

Frequently asked questions

Why does my Philadelphia rowhouse basement smell musty?
Usually moisture: groundwater through old masonry, a plumbing leak, or humid summer air condensing on cool walls. The Pennsylvania Department of Health advises repairing leaks and using a dehumidifier and vent fans.
Is white powder on my basement wall mold?
Often it is mineral deposit left where water moves through brick or stone, though only an inspection can say for certain. Either way it points to moisture that needs to be found.
Will a dehumidifier alone fix basement mold?
It helps control humidity, and EPA suggests staying below 60 percent, ideally 30 to 50 percent. It does not stop a leak or remove growth that is already there.
Do I need a permit to remove moldy drywall in Philadelphia?
Philadelphia L&I says gypsum wallboard installed over existing wall surfaces in one- or two-family dwellings does not need a permit, and ordinary maintenance repairs generally need none. For larger work, ask the contractor and L&I.
Call now to be connected with a local mold remediation company in Philadelphia.
(215) 774-2847

Last updated:

☎ Call (215) 774-2847